Kia Niro: Lubrication System / Oil Pan Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Engine Mechanical System / Lubrication System / Oil Pan Repair procedures

Removal

1.	Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")

2.	Drain engine oil. (Refer to Lubrication System - "Engine Oil")

Remove the oil pan (A).

(1)	Unfasten the bolts.

(2)

Insert the blade of SST (09215-3C000) between the lower crankcase and the oil pan. Separate the applied sealer and remove the oil pan.

Loosen one oil pan bolt near each corner of the oil pan leaving the bolts held in by about 2 threads.

Then remove all other pan bolts.

•	Insert the SST between the oil pan and the lower crankcase by tapping it with a plastic hammer in the direction of ① arrow.

•	After tapping the SST with a plastic hammer along the direction of ② arrow around more than 2/3 edge of the oil pan, remove it from the lower crankcase.

•	Do not turn over the SST abruptly without tapping as it may damage the SST.

•	Be careful not to damage the contacting surfaces of the lower crankcase and the oil pan.

4.	Remove the oil screen (A) with the gasket.

Installation

Install the oil screen (A) with a new gasket.

Tightening torque :

24.5 - 31.4 N·m (2.5 - 3.2 kgf·m, 18.1 - 23.1 lb·ft)

Install the oil pan.

(1)	Using a gasket scraper, remove all the old packing material from the gasket surfaces.

(2)	The sealant locations on the oil pan and the lower crankcase must be free of harmful foreign materials, oil, dust and moisture. Spray cleaner on the surface and wipe with a clean duster.

(3)

After applying liquid sealant on the oil pan, assemble it within 5 minutes of applying sealant.

Continuous bead of sealant should be applied to prevent any path of oil leakage.

Sealant :

THREE BOND 1217H or LOCTITE 5900H

•	When applying sealant gasket, sealant must not protrude inside the oil pan.

•	To prevent leakage of oil, apply sealant gasket on the inner threads of the bolt holes.

•	If the sealant is applied to the bottom surface of the lower crankcase, it should be in the same location as the oil pan.

(4)

Install the oil pan (A). Uniformly tighten the bolts in several passes.

Tightening torque :

9.8 - 11.8 N·m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb·ft)

•	After assembly, wait at least 30 minutes before filling the engine with oil.

•	Always use a new drain plug gasket.

3.	Refill engine with engine oil.

Oil Pan Components and components location

Components 1. Oil pan 2. Drain plug gasket 3. Drain plug 4. Oil screen 5. Oil screen gasket ...

Oil Cooler Repair procedures

Removal 1. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover") 2. Drain the ...

Other information:

Kia Niro (DE HEV) Owners Manual: To temporarily accelerate with the cruise control on
If you want to speed up temporarily when the cruise control is on, depress the accelerator pedal. Increased speed will not interfere with cruise control operation or change the set speed. To return to the set speed, take your foot off the accelerator. If you move the lever down (to SET-) at i ...

Kia Niro (DE HEV) Owners Manual: Warning
If you cross a lane, the lane you cross will blink (yellow) and symbol will blink green on LCD with an audible warning during max 3 seconds. If the steering wheel appears, the system will control the vehicle’s steering to prevent the vehicle from crossing the lane. If all the ...