Kia Niro: Fuel Delivery System / Fuel pressure test (low pressure system)

Fuel Pressure Test (Low pressure system)
1.

Release the residual pressure in fuel line.

(Refer to the Fuel Delivery System - Inspection - "Release Residual Pressure in Fuel Line").

  

When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the KDS/GDS after completion of “Release Residual Pressure in Fuel Line” work.

2.

Install the Special Service Tool (SST).

(1)

Disconnect the fuel feed tube from the delivery pipe.

  

There may be some residual pressure even after completing “Release Residual Pressure in Fuel Line”, so cover the hose connection with a shop towel to prevent residual fuel from spilling out before disconnecting any fuel connection.

(2)

Install the special service tool for measuring the fuel pressure in between the fuel feed tube and the fuel delivery pipe (Refer to the figure below).

For 09353-02100

For 0K353-D4100

3.

Inspect fuel leakage on connections among the fuel feed tube, the delivery pipe, and the SST components with ignition "ON".

4.

Measure the fuel pressure.

(1)

Start the engine and measure the fuel pressure at idle.

Fuel Pressure: Over 290 kPa (Over 2.9 bar, Over 2.95 kgf/cm², Over 42.06 psi)

  

If the fuel pressure does not satisfy the specification, repair or replace the related part. (Refer to the table below.)

Fuel
Pressure
Cause
Related Part
Too Low
Fuel filter clogged
Fuel Filter
Fuel leakage
Fuel Pressure Regulator
Too High
Fuel pressure regulator stuck
Fuel Pressure Regulator

(2)

Stop the engine, and then check for the change in the fuel pressure gauge reading.

Standard Value: The gauge reading should hold for about 5 minutes after the engine stops

  

If the gauge reading could not be held, repair or replace the related part. (Refer to the table below.)

Fuel Pressure
(After Engine Stops)
Cause
Related
Part
Fuel Pressure Drops Slowly
Leakage on injector
Injector
Fuel Pressure Drops Immediately
Check valve of fuel pump stuck open
Fuel Pump

(3)

Switch "OFF" the ignition.

5.

Release the residual pressure in fuel line.

(Refer to the Fuel Delivery System - Repair Procedures - "Release Residual Pressure in Fuel Line").

  

When removing the fuel pump fuse, a Diagnostic Trouble Code (DTC) may occur. Delete the code with the KDS/GDS after completion of “Release Residual Pressure in Fuel Line” work.

6.

Finish test.

(1)

Remove the Special Service Tool (SST) from the low pressure fuel feed tube and the low pressure inlet of high pressure fuel pump.

(2)

Connect the low pressure fuel feed tube and the low pressure inlet of high pressure fuel pump.

Components and components location
Components Location [Fuel Tank Assembly] 1. Fuel Tank 2. Fuel Pump Assembly 3. Canister 4. Fuel Tank Air Filter 5. Fuel Tank Band ...

Release residual pressure in fuel line
Release Residual Pressure in Fuel Line    Whenever the high pressure fuel fuse, fuel pipe, delivery pipe, or injecto ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Mass Air Flow Sensor (MAFS) Description and operation
Description MAFS uses a sensing element made of a hot-film to measure the mass of intake air entering the engine and to send the signal to the ECM. A large amount of intake air represents acceleration or high load conditions while a small amount of intake air represents decelerati ...

Kia Niro 2017 (DE HEV) Service Manual: Components and components location
Components 1. Rear bumper cover assembly 2. Rear Bumper Beam Assembly 3. Rear bumper side under cover [RH] 4. Rear bumper side bracket [RH] 5. Rear bumper side under cover [LH] 6. Rear bumper side bracket [LH] ...

© 2016-2024 www.kniro.net