Kia Niro: Power Train / Engine Oil and Filter Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Maintenance / Power Train / Engine Oil and Filter Repair procedures

Inspection

Engine Oil Level

Be sure that the vehicle is on level ground.

1.	Warm up and stop the engine, and then wait for 5 minutes.

2.	Turn the engine off and wait for a few minutes (about 5 minutes) for the oil to return to the oil pan.

3.	Pull the dipstick out, wipe and re-insert it fully.

4.	Check that the oil level is between the "L" level mark and "F" level mark on the engine oil level gauge.

If the level is low, check for leakage and add oil up to the full level mark.

Use a funnel to help prevent oil from being spilled on engine components.

Do not fill the engine with oil to above the full level mark.

Engine Oil Appearance

1.	Check engine oil for white turbidity or heavy contamination.

2.	If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant. Repair or replace damaged parts.

Replacement

•	Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

•	Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.

•	In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.

1.	Park the car on level ground.

Drain engine oil.

(1)	Remove the oil filler cap (A).

(2)	Remove the drain under cover (A).

(3)	After lifting the car, remove the oil drain plug (A) and drain oil into a container.

Replace the oil filter.

(1)	Remove the oil filter cover (A).

(2)	Using the SST (09263-2E000), remove the oil filter (A).

(3)	Check and clean the oil filter installation surface.

(4)	Check the part number of the new oil filter is as same as old one.

(5)	Apply clean engine oil to the gasket of a new oil filter.

(6)	Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.

(7)

Tighten it with the torque below.

Tightening torque :

11.8 - 15.7 N·m (1.2 - 1.6 kgf·m, 8.7 - 11.6 lb·ft)

(8)	Install the oil filter cover (A).

Refill with the engine oil.

(1)

Install the oil drain plug with a new gasket (A).

Tightening torque :

34.3 - 44.1 N·m (3.5 - 4.5 kgf·m, 25.3 - 32.5 lb·ft)

(2)	Install the drain under cover (A).

(3)

Fill with new engine oil while checking the oil level on the dipstick.

Capacity

Total :

4.1 L (1.08 U.S.gal., 4.33 U.S.qt., 3.61 lmp.qt.)

Oil pan :

3.4 L (0.90 U.S.gal., 3.59 U.S.qt., 2.99 lmp.qt.)

Drain and refill including oil filter :

3.8 L (1.00 U.S.gal., 4.02 U.S.qt., 3.34 lmp.qt.)

•	Fill the crankcase to about half the capacity and then fill the remainder after waiting.

•	Do not fill oil over the 'F' line and check frequently the level with the oil level gauge to ensure no overfilling.

(4)	Install the oil filler cap (A) and the oil dipstick.

5.	Start the engine and check that no oil is leaking from the drain plug or oil filter.

Recheck the engine oil level.

When rechecking the engine oil level, be sure to warm up the engine sufficiently. If the engine has not warmed up sufficiently, the measured engine oil level may be less than the specification.

Drive Belt Repair procedures

Inspection 1. Check belt for maintenance and abnormal wear of V-ribbed part. Replace if necessary. ...

Exhaust System Repair procedures

Inspection 1. Visually check the pipes, hangers and connections for severe corrosion, leaks or damage. 2. Check for unusual exhaust sounds or ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Safety Plug Description and operation
Description Safety Plug is installed on the rear side of the high voltage battery and it can mechanically shut the high voltage circuit off when servicing the high voltage system (i.e. High Voltage Battery, Power Relay Assembly, HPCU, BMS ECU, Hybrid Drive Motor, Inverter, HSG, LD ...

Kia Niro (DE HEV) Owners Manual: Jump starting procedure
1.Make sure the booster battery is 12-volt and that its negative terminal is grounded. 2.If the booster battery is in another vehicle, do not allow the vehicles come in contact. 3.Turn off all unnecessary electrical loads. 4.Connect the jumper cables in the exact sequence shown in the illustr ...