Kia Niro: Engine Control System / Engine Control Module (ECM) Repair procedures
| Removal |
| 1. |
Switch "OFF" the ignition and disconnect the negative (-) battery terminal. |
| 2. |
Disconnect the TCM connectors (A). |
| 3. |
Disconnect the ECM connectors (B).
|
| 4. |
Remove the ECM & TCM bracket (B) after loosening the mounting nuts (A).
|
| 5. |
Remove the ECM (B) after loosening the mounting nuts (A) from the ECM & TCM bracket.
|
| Installation |
| 1. |
Install in the reverse order of removal. |
| ECM Problem Inspection Procedure |
| 1. |
TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.
|
| 2. |
TEST ECM CONNECTOR: Disconnect the ECM connector and visually check the ground terminals on ECM side and harness side for bent pins or poor contact pressure. If the problem is found, repair it. |
| 3. |
If problem is not found in steps 1 and 2, the ECM could be faulty. In this case, make sure that there are no DTC's before replacing the ECM with a new one, and then check the vehicle again. If DTC's are found, examine them first before replacing the ECM. |
| 4. |
RE-TEST THE ORIGINAL ECM: Install the original ECM (possibly broken) into a known-good vehicle and check the vehicle. If the problem reoccurs, replace the original ECM with a new one. If problem does not reoccur, this is an intermittent problem. (Refer to “Intermittent Problem Inspection Procedure” in Basic Inspection Procedure.) |
| Adjustment |
ECM Neutral Mode procedure (With Immobilizer)
| • |
After replacing the ECM of the vehicle with the immobilizer, the following procedure must be performed. |
|
[If installing a used ECM] |
| 1) |
Perform "ECM Neutral Mode" procedure using KDS/GDS. (Refer to "Body Electrical System - "Immobilizer System - Repair procedures") |
| 2) |
After finishing "ECM Neutral Mode", perform "Key Teaching" procedure using KDS/GDS. (Refer to "Body Electrical System - "Immobilizer System - Repair procedures") |
|
[If installing a new ECM] Perform "Key Teaching" procedure using KDS/GDS. (Refer to "Body Electrical System - "Immobilizer System - Repair procedures") |
ECM Neutral Mode procedure (With Smart key)
| • |
After replacing the ECM of the vehicle with the smart key system (button start), the following procedure must be performed. |
|
[If installing a used ECM] |
| 1) |
Perform "ECM Neutral Mode" procedure using KDS/GDS. (Refer to "Body Electrical System - "Smart key System - Repair procedures") |
| 2) |
After finishing "ECM Neutral Mode", turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. (Refer to "Body Electrical System - "Smart key System - Repair procedures") |
|
[If installing a new ECM] Turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. (Refer to "Body Electrical System - "Smart key System - Repair procedures") |
ETC module learning procedure
Perform ETC module learning after replacing the ETC module.
(Refer to Electronic Throttle Control System - "Adjustment")
VIN programming procedure
VIN (Vehicle Identification Number) is a number with the vehicle's information (Maker, Vehicle Type, Vehicle Line/Series, Body Type, Engine Type, Transmission Type, Model Year, Plant Location and so forth. For more information, please refer to "GI" group in this SERVICE MANUAL.). When replacing an ECM, the VIN must be programmed in the ECM. If there is no VIN in ECM memory, the fault code (DTC P0630) is set.
Carefully check the VIN as it cannot be changed once programmed. |
| 1. |
Select "VIN Writing" function in "Vehicle S/W Management". |
| 2. |
Select "Write VIN" in "ID Register" menu.
|
| 3. |
Enter the VIN.
|
Engine Control Module (ECM) Schematic diagrams
ECM Terminal And Input/Output
signal
ECM Terminal Function
Connector [A]
Pin No.
Description
Connected to
1
...
ETC (Electronic Throttle Control) System Specifications
Specification
[Throttle Position
Sensor (TPS)]
Throttle angle(°)
Output Voltage (V) [Vref=5V]
TPS1
TPS2
0
...
Other information:
Kia Niro 2017 (DE HEV) Service Manual: Seat Heater Components and components location
Component Location
Front Seat Heater
1. Seat heater unit (Assist seat only)
2. Front seat back heater
3. Front seat cushion heater
Front Seat Heater (Air Ventilation)
1. Air ventilation seat unit (A ...
Kia Niro 2017 (DE HEV) Service Manual: Intake Actuator Components and components location
Components Location
1. Intake actuator
...
