Kia Niro: AHB(Active Hydraulic Boost) System / Description and operation
| Description |
Regeneration Brake System
During deceleration or braking of an electric vehicle or HEV, the drive motor acts as an alternator and charges the battery by converting the vehicle’s kinetic energy generated during braking into electrical energy. Regenerative braking amount depends on the vehicle speed, battery SOC, etc. Achieves significant improvement in fuel efficiency in city driving with repeated acceleration and deceleration.
Regenerative Braking Cooperation Control (RBC)
The brake force apportion is distributed by controlling hydraulic braking and the total brake force (hydraulic + regenerative brake) output that the driver requires is generated.In the case of regenerative brake failure, the total brake force that the driver requires is supplied by the hydraulic brake system.
The AHB system is composed of the Pressure Source Unit (PSU), the Intergrated Brake Actuation Unit (IBAU). First, the PSU generates the hydraulic pressure required for braking.Similar to the boosting effect when the driver steps on the brake pedal in a system equipped with a vacuum booster, the hydraulic pressure stored in the cylinder is supplied to provide pressure throughout the entire brake line.Second, the IBAU delivers pressure that is generated by the PSU to a caliper on each wheel. It is connected to the brake pedal to detect the brake force that is required by the driver, and to generate a brake feeling.The IBAU carries out the ABS, TCS, and ESC functions as in conventional vehicles.
| AHB System Operation Principals |
| 1. |
Initial Status
High pressure (180 bar) between the PSU and the IBAU is generated consistently. Therefore, before removing the PSU or the IBAU, high pressure between them should be reduced for safety by conducting "High pressure release mode" of GDS connected. |
| 2. |
Brake operation
Apply Mode : During normal braking, IN valve becomes ON and opens; then, the high pressure generated by PSU is supplied to a caliper on each wheel by IBAU and the brake operation is engaged.Release Mode : During discharging brake, OUT valve opens and IN valve closes; then, the high pressure of brake oil return back to reservoir. At this time, CUT valve is ON and it prevents back flow of brake oil to master cylinder. |
| 3. |
Brake malfunction
If the PSU or the IBAU is broken, IN valve and OUT valve are closed, and CUT valve is off. Therefore, the brake force is generated by only pressing a brake pedal manually by a driver. |
Operation and Leakage Check
Check all of the following items:
|
Items |
Recommended |
|
Integrated Brake Actuation Unit (IBAU) (A) and Pressure Source Unit (PSU)
(B) |
Check brake operation by applying the brakes during a test drive. If the
brakes do not work properly, check the IBAU and PSU. Replace IBAU and PSU
as an assembly if it does not work properly or if there are signs of leakage.
|
|
Piston cup and pressure cup inspection (A & B) |
Check brake operation by applying the brakes. Look for damage or signs of
fluid leakage. Replace the IBAU as an assembly if the pedal does not work
properly or if there is damage or signs of fluid leakage. |
|
Brake hoses (C) |
Look for damage or signs of fluid leakage. Replace the brake hose with a
new one if it is damaged or leaking. |
|
Caliper piston seal and piston boots (D) |
Check brake operation by applying the brakes.Look for damage or signs of
fluid leakage. If the pedal does not work properly, the brakes drag, or
there is damage or signs of fluid leakage, disassemble and inspect the brake
caliper. Replace the boots and seals with new ones whenever the brake caliper
is disassembled." |
Brake Actuation Unit Components and components location
Components
1. Integrated Brake Actuation Unit (IBAU) ECU
2. Reservoir
3. Pedal simulator
4. Integrated Brake Actuation Unit (IBAU)
...
Other information:
Kia Niro 2017 (DE HEV) Service Manual: Wireless Charging Lamp Repair procedures
Removal
•
Handling wireless charging system parts by wet hands may cause
electric shock.
•
Put on gloves to protect your hands.
...
Kia Niro (DE HEV) Owners Manual: Operation tips
For maximum defrosting, set the temperature control to the extreme right/hot
position and the fan speed control to the highest speed.
If warm air to the floor is desired while defrosting or defogging, set the
mode to the floor-defrost position.
Before driving, clear all snow and ice fro ...
