Kia Niro: Brake System / Brake bleeding prcoedures
| AHB Brake System Bleeding
procedure |
| • |
Do not reuse the drained fluid.
|
| • |
Always use genuine DOT3/DOT4 brake Fluid. Usinga non-genuine
DOT3/DOT4 brake fluid can causecorrosion and decrease the life of
the system.
|
| • |
Make sure no dirt or other foreign matter is allowed tocontaminate
the brake fluid.
|
| • |
Do not spill brake fluid on the vehicle, it may damagethe paint;
if brake fluid does contact the paint, wash itoff immediately with
water.
|
| • |
When bleeding air, make sure the brake fluid is above10mm starting
from the “MIN” line.
|
| • |
To remove the reservoir tank cap to refill the brakefluid, always
close the air shut-off valve of the SST.
|
|
Air Bleeding Tool Installation
Procedure
|
To prevent the brake fluid reservoir tank from beingdamaged and ensure
the safety of worker, set thepressure of the gauge to the standard value
beforeinstalling the SST.
|
| 1. |
Before installing the SST on the vehicle, close the airshut-off valve
(A) to adjust the pressure gauge to thestandard value.
|
For safety of worker and correct pressure setting,make sure that
the plug (B) is installed correctly.
|
|
| 2. |
After connecting an air hose and opening the airshut-off valve (A), adjust
the pressure gauge (B) withto the standard value.
|
Standard pressure value:sp
0.3 - 0.5MPa (43.5 - 72.5psi)
|
|
| 3. |
close the air shut off valve (A) and remove the plug(B).
|
For safety of worker, make sure that the air shut offvalve is
closed and remove the plug.
|
|
| 4. |
Remove the brake reservoir tank cap.
|
| 5. |
Install the cap (A) of SST (0k585-E8100) on thereservoir tank.
|
| 6. |
Make sure the check valve (A) is closed and connectSST(09580-3D100) (A)
to the adapter (B).
|
Air Bleeding Tool Removal
Procedure
| 1. |
To remove the SST (09580-3D100) from the vehicle,close the air shut-off
valve (A) first.
|
| 2. |
After disconnecting the air hose (B), bleed air in thereservoir tank
by opening the air shut-off valve (A)slowly.
|
To prevent backflow of brake fluid, be sure to openthe air shut-off
valve slowly then bleed air in thereservoir tank.
|
|
| 3. |
Remove SST (09580-3D100) and the cap of SST(0k585-E8100) on the reservoir
tank.
|
| 4. |
Inatall the brake reservoir tank cap.
|
AHB Brake System Bleeding
Step 1 (IBAU ECU OFF)
|
IBAU filled with brake oil should be used for bleeding.
|
| 1. |
Disconnect the negative (-) battery terminal to turn off IBAU ECU.
|
| 2. |
Set the air bleeding tool (SST: 09580-3D100) and the cap of SST (0k585-E8100)to
reservoir tank and make pressure (0.3-0.5MPa (43.5 - 72.5psi)) to it.
|
| 3. |
Initiate air bleeding on all bleed screws in the following sequences
until air bubbles no longer appear in the fluid. After air bleeding, close
the bleed screws.
? PSU ? IBAU (2 bleed srews) ? 4 wheels (15 seconds for each)
|
| 4. |
Perform air bleeding while stepping on the brake pedal and opening bleed
screws; then, close bleed screws and release the brake pedal. Perform this
procedure 10 times.
| – |
Bleed screw sequence : ? IBAU (2 bleed srews) ? 4 wheels
|
| – |
Repeat it until air bubbles no longer appear in the fluid
|
| – |
Be cautious that air come in the brake line with opening the
bleed screws too much.
|
|
AHB Brake System Bleeding
Step 2 (IBAU ECU ON)
| 1. |
Connect the negative (-) battery terminal to turn on IBAU ECU.
|
| 2. |
Set the ECU S/W to air bleeding mode on the brake system.
|
Setting the ECU S/W to air bleeding mode in 30 seconds.
|
| (1) |
After turning IGN ON with the engine start button, set the front
wheels straight forward and the shift lever knob in Parking.
|
| (2) |
Press and release the brake pedal 10 times while pushing the
VDC OFF switch. Make sure to press the brake pedal more than 40
mm and realease it fully without any step on.
|
| (3) |
Turn off the engine start button; then, start the engine and
turn on the "VDC off" switch.
|
The air bleeding mode is deceased in each following condition.
| (1) |
IGN OFF and shift lever knob in D/R/N
|
| (3) |
Brake fluid level is under "MIN".
|
| (4) |
Turn off the "VDC off" switch.
|
|
| 3. |
Use the air bleeding tool (SST: 09580-3D100, 0K585-E8100) and feed oil
pressure 0.3 - 0.5MPa (43.5 - 72.5psi) into the reservoir.
Loosen the bleed screws on 4 wheels; then, initiate air bleeding and
close them while depressing the brake pedal half stroke continuously. Perform
it 10 times; then, release the brake pedal.
|
| 4. |
Connect the GDS to the data link connector located underneath the dash
panel and perform "Fluid Circulation Mode" on GDS.
Fluid Circulation Mode is to remove air bubble in the brake fluid, which
is realeased into the air while circulating the brake fluid inside the IBAU
to the reservior tank.
|
High Voltage Shut-off Procedures
•
Be sure to read and follow the “General Safety Informat ...
Specifications
Item
Specification
Front disc brake
Type
Ventilated disc
Disc O.D.
O 280 mm ...
Other information:
Kia Niro 2017 (DE HEV) Service Manual: Description and operation
Description
It's a system that uses illumination sensor to automatically turn ON the tail
lamp and head lamp based on the change in surrounding environment's illumination
condition. It activates when the vehicle enters/exits tunnel, or when the illumination
condition in su ...
Kia Niro (DE HEV) Owners Manual: In case of an emergency while driving
If the engine stalls at a crossroad or crossing
• If the engine stalls at a crossroad or crossing, set the shift lever in the
N (Neutral) position and then push the vehicle to a safe place.
If you have a flat tire while driving
If a tire goes flat while you are driving:
1. Take your foot off ...
High voltage shut-off procedures
Specifications